Petroleum

From Wikipedia, the free encyclopedia - View original article

 
Jump to: navigation, search
Proven world oil reserves, 2009
Pumpjack pumping an oil well near Lubbock, Texas
An oil refinery in Mina-Al-Ahmadi, Kuwait

Petroleum (L. petroleum, from Greek: πέτρα (rock) + Latin: oleum (oil)[1][2][3]) is a naturally occurring, yellow-to-black liquid found in geologic formations beneath the Earth's surface, which is commonly refined into various types of fuels. It consists of hydrocarbons of various molecular weights and other liquid organic compounds.[4] The name petroleum covers both naturally occurring unprocessed crude oil and petroleum products that are made up of refined crude oil. A fossil fuel, petroleum is formed when large quantities of dead organisms, usually zooplankton and algae, are buried underneath sedimentary rock and subjected to intense heat and pressure.

Petroleum is recovered mostly through oil drilling. This comes after the studies of structural geology (at the reservoir scale), sedimentary basin analysis, reservoir characterization (mainly in terms of the porosity and permeability of geologic reservoir structures).[5][6] It is refined and separated, most easily by boiling point, into a large number of consumer products, from gasoline (petrol) and kerosene to asphalt and chemical reagents used to make plastics and pharmaceuticals.[7] Petroleum is used in manufacturing a wide variety of materials,[8] and it is estimated that the world consumes about 90 million barrels each day.

The use of fossil fuels such as petroleum has a negative impact on Earth's biosphere, releasing pollutants and greenhouse gases into the air and damaging ecosystems through events such as oil spills. Concern over the depletion of the earth's finite reserves of oil, and the effect this would have on a society dependent on it, is a concept known as peak oil.

Etymology[edit]

The word petroleum comes from Greek: πέτρα (petra) for rocks and Greek: ἔλαιον (elaion) for oil. The term was found (in the spelling "petraoleum") in 10th-century Old English sources.[9] It was used in the treatise De Natura Fossilium, published in 1546 by the German mineralogist Georg Bauer, also known as Georgius Agricola.[10] In the 19th century, the term petroleum was frequently used to refer to mineral oils produced by distillation from mined organic solids such as cannel coal (and later oil shale), and refined oils produced from them; in the United Kingdom, storage (and later transport) of these oils were regulated by a series of Petroleum Acts, from the Petroleum Act 1862 onwards.

History[edit]

Early history[edit]

Oil derrick in Okemah, Oklahoma, 1922.

Petroleum, in one form or another, has been used since ancient times, and is now important across society, including in economy, politics and technology. The rise in importance was due to the invention of the internal combustion engine, the rise in commercial aviation, and the importance of petroleum to industrial organic chemistry, particularly the synthesis of plastics, fertilizers, solvents, adhesives and pesticides.

More than 4000 years ago, according to Herodotus and Diodorus Siculus, asphalt was used in the construction of the walls and towers of Babylon; there were oil pits near Ardericca (near Babylon), and a pitch spring on Zacynthus.[11] Great quantities of it were found on the banks of the river Issus, one of the tributaries of the Euphrates. Ancient Persian tablets indicate the medicinal and lighting uses of petroleum in the upper levels of their society. By 347 AD, oil was produced from bamboo-drilled wells in China.[12] Early British explorers to Myanmar documented a flourishing oil extraction industry based in Yenangyaung, that in 1795 had hundreds of hand-dug wells under production.[13] The mythological origins of the oil fields at Yenangyaung, and its hereditary monopoly control by 24 families, indicate very ancient origins.

Modern history[edit]

In 1847, the process to distill kerosene from petroleum was invented by James Young. He noticed a natural petroleum seepage in the Riddings colliery at Alfreton, Derbyshire from which he distilled a light thin oil suitable for use as lamp oil, at the same time obtaining a thicker oil suitable for lubricating machinery. In 1848 Young set up a small business refining the crude oil.

Young eventually succeeded, by distilling cannel coal at a low heat, in creating a fluid resembling petroleum, which when treated in the same way as the seep oil gave similar products. Young found that by slow distillation he could obtain a number of useful liquids from it, one of which he named "paraffine oil" because at low temperatures it congealed into a substance resembling paraffin wax.[14]

The production of these oils and solid paraffin wax from coal formed the subject of his patent dated 17 October 1850. In 1850 Young & Meldrum and Edward William Binney entered into partnership under the title of E.W. Binney & Co. at Bathgate in West Lothian and E. Meldrum & Co. at Glasgow; their works at Bathgate were completed in 1851 and became the first truly commercial oil-works in the world with the first modern oil refinery, using oil extracted from locally-mined torbanite, shale, and bituminous coal to manufacture naphtha and lubricating oils; paraffin for fuel use and solid paraffin were not sold till 1856.[15]

Shale bings near Broxburn, 3 of a total of 19 in West Lothian

Another early refinery was built by Ignacy Łukasiewicz, providing a cheaper alternative to whale oil. The demand for petroleum as a fuel for lighting in North America and around the world quickly grew.[16] Edwin Drake's 1859 well near Titusville, Pennsylvania, is popularly considered the first modern well. Drake's well is probably singled out because it was drilled, not dug; because it used a steam engine; because there was a company associated with it; and because it touched off a major boom.[17] However, there was considerable activity before Drake in various parts of the world in the mid-19th century. A group directed by Major Alexeyev of the Bakinskii Corps of Mining Engineers hand-drilled a well in the Baku region in 1848.[18] There were engine-drilled wells in West Virginia in the same year as Drake's well.[19] An early commercial well was hand dug in Poland in 1853, and another in nearby Romania in 1857. At around the same time the world's first, small, oil refinery was opened at Jasło in Poland, with a larger one opened at Ploiești in Romania shortly after. Romania is the first country in the world to have had its annual crude oil output officially recorded in international statistics: 275 tonnes for 1857.[20][21]

The first commercial oil well in Canada became operational in 1858 at Oil Springs, Ontario (then Canada West).[22] Businessman James Miller Williams dug several wells between 1855 and 1858 before discovering a rich reserve of oil four metres below ground.[23] Williams extracted 1.5 million litres of crude oil by 1860, refining much of it into kerosene lamp oil.[22] William's well became commercially viable a year before Drake's Pennsylvania operation and could be argued to be the first commercial oil well in North America.[22] The discovery at Oil Springs touched off an oil boom which brought hundreds of speculators and workers to the area. Advances in drilling continued into 1862 when local driller Shaw reached a depth of 62 metres using the spring-pole drilling method.[24] On January 16, 1862, after an explosion of natural gas Canada's first oil gusher came into production, shooting into the air at a recorded rate of 3,000 barrels per day.[25] By the end of the 19th century the Russian Empire, particularly the Branobel company in Azerbaijan, had taken the lead in production.[26]

Access to oil was and still is a major factor in several military conflicts of the twentieth century, including World War II, during which oil facilities were a major strategic asset and were extensively bombed.[27] The German invasion of the Soviet Union included the goal to capture the Baku oilfields, as it would provide much needed oil-supplies for the German military which was suffering from blockades.[28] Oil exploration in North America during the early 20th century later led to the U.S. becoming the leading producer by mid-century. As petroleum production in the U.S. peaked during the 1960s, however, the United States was surpassed by Saudi Arabia and the Soviet Union.

Today, about 90 percent of vehicular fuel needs are met by oil. Petroleum also makes up 40 percent of total energy consumption in the United States, but is responsible for only 1 percent of electricity generation. Petroleum's worth as a portable, dense energy source powering the vast majority of vehicles and as the base of many industrial chemicals makes it one of the world's most important commodities. Viability of the oil commodity is controlled by several key parameters, number of vehicles in the world competing for fuel, quantity of oil exported to the world market (Export Land Model), Net Energy Gain (economically useful energy provided minus energy consumed), political stability of oil exporting nations and ability to defend oil supply lines.

The top three oil producing countries are Russia, Saudi Arabia, and the United States.[29] About 80 percent of the world's readily accessible reserves are located in the Middle East, with 62.5 percent coming from the Arab 5: Saudi Arabia, UAE, Iraq, Qatar and Kuwait. A large portion of the world's total oil exists as unconventional sources, such as bitumen in Canada and oil shale in Venezuela. While significant volumes of oil are extracted from oil sands, particularly in Canada, logistical and technical hurdles remain, as oil extraction requires large amounts of heat and water, making its net energy content quite low relative to conventional crude oil. Thus, Canada's oil sands are not expected to provide more than a few million barrels per day in the foreseeable future.

Conventional crude oil production, those having Net Energy Gain above 10 stopped growing in 2005 at about 74 million barrels per day (11,800,000 m3/d). The International Energy Agency's (IEA) 2010 World Energy Outlook estimated that conventional crude oil production has peaked and is depleting at 6.8 percent per year.[citation needed] US Joint Forces Command's Joint Operating Environment 2010 issued this warning to all US military commands "By 2012, surplus oil production capacity could entirely disappear, and as early as 2015, the shortfall in output could reach nearly 10 million barrels per day."[citation needed]

Composition[edit]

In its strictest sense, petroleum includes only crude oil, but in common usage it includes all liquid, gaseous, and solid hydrocarbons. Under surface pressure and temperature conditions, lighter hydrocarbons methane, ethane, propane and butane occur as gases, while pentane and heavier ones are in the form of liquids or solids. However, in an underground oil reservoir the proportions of gas, liquid, and solid depend on subsurface conditions and on the phase diagram of the petroleum mixture.[30]

An oil well produces predominantly crude oil, with some natural gas dissolved in it. Because the pressure is lower at the surface than underground, some of the gas will come out of solution and be recovered (or burned) as associated gas or solution gas. A gas well produces predominantly natural gas. However, because the underground temperature and pressure are higher than at the surface, the gas may contain heavier hydrocarbons such as pentane, hexane, and heptane in the gaseous state. At surface conditions these will condense out of the gas to form natural gas condensate, often shortened to condensate. Condensate resembles petrol in appearance and is similar in composition to some volatile light crude oils.

The proportion of light hydrocarbons in the petroleum mixture varies greatly among different oil fields, ranging from as much as 97 percent by weight in the lighter oils to as little as 50 percent in the heavier oils and bitumens.

The hydrocarbons in crude oil are mostly alkanes, cycloalkanes and various aromatic hydrocarbons while the other organic compounds contain nitrogen, oxygen and sulfur, and trace amounts of metals such as iron, nickel, copper and vanadium. The exact molecular composition varies widely from formation to formation but the proportion of chemical elements vary over fairly narrow limits as follows:[31]

Most of the world's oils are non-conventional.[32]
Composition by weight
ElementPercent range
Carbon83 to 85%
Hydrogen10 to 14%
Nitrogen0.1 to 2%
Oxygen0.05 to 1.5%
Sulfur0.05 to 6.0%
Metals< 0.1%

Four different types of hydrocarbon molecules appear in crude oil. The relative percentage of each varies from oil to oil, determining the properties of each oil.[30]

Composition by weight
HydrocarbonAverageRange
Alkanes (paraffins)30%15 to 60%
Naphthenes49%30 to 60%
Aromatics15%3 to 30%
Asphaltics6%remainder

Crude oil varies greatly in appearance depending on its composition. It is usually black or dark brown (although it may be yellowish, reddish, or even greenish). In the reservoir it is usually found in association with natural gas, which being lighter forms a gas cap over the petroleum, and saline water which, being heavier than most forms of crude oil, generally sinks beneath it. Crude oil may also be found in semi-solid form mixed with sand and water, as in the Athabasca oil sands in Canada, where it is usually referred to as crude bitumen. In Canada, bitumen is considered a sticky, black, tar-like form of crude oil which is so thick and heavy that it must be heated or diluted before it will flow.[33] Venezuela also has large amounts of oil in the Orinoco oil sands, although the hydrocarbons trapped in them are more fluid than in Canada and are usually called extra heavy oil. These oil sands resources are called unconventional oil to distinguish them from oil which can be extracted using traditional oil well methods. Between them, Canada and Venezuela contain an estimated 3.6 trillion barrels (570×10^9 m3) of bitumen and extra-heavy oil, about twice the volume of the world's reserves of conventional oil.[34]

Petroleum is used mostly, by volume, for producing fuel oil and petrol, both important "primary energy" sources.[35] 84 percent by volume of the hydrocarbons present in petroleum is converted into energy-rich fuels (petroleum-based fuels), including petrol, diesel, jet, heating, and other fuel oils, and liquefied petroleum gas.[36] The lighter grades of crude oil produce the best yields of these products, but as the world's reserves of light and medium oil are depleted, oil refineries are increasingly having to process heavy oil and bitumen, and use more complex and expensive methods to produce the products required. Because heavier crude oils have too much carbon and not enough hydrogen, these processes generally involve removing carbon from or adding hydrogen to the molecules, and using fluid catalytic cracking to convert the longer, more complex molecules in the oil to the shorter, simpler ones in the fuels.

Due to its high energy density, easy transportability and relative abundance, oil has become the world's most important source of energy since the mid-1950s. Petroleum is also the raw material for many chemical products, including pharmaceuticals, solvents, fertilizers, pesticides, and plastics; the 16 percent not used for energy production is converted into these other materials. Petroleum is found in porous rock formations in the upper strata of some areas of the Earth's crust. There is also petroleum in oil sands (tar sands). Known oil reserves are typically estimated at around 190 km3 (1.2 trillion (short scale) barrels) without oil sands,[37] or 595 km3 (3.74 trillion barrels) with oil sands.[38] Consumption is currently around 84 million barrels (13.4×10^6 m3) per day, or 4.9 km3 per year. Which in turn yields a remaining oil supply of only about 120 years, if current demand remain static.

Chemistry[edit]

Octane, a hydrocarbon found in petroleum. Lines represent single bonds; black spheres represent carbon; white spheres represent hydrogen.

Petroleum is a mixture of a very large number of different hydrocarbons; the most commonly found molecules are alkanes (paraffins), cycloalkanes (naphthenes), aromatic hydrocarbons, or more complicated chemicals like asphaltenes. Each petroleum variety has a unique mix of molecules, which define its physical and chemical properties, like color and viscosity.

The alkanes, also known as paraffins, are saturated hydrocarbons with straight or branched chains which contain only carbon and hydrogen and have the general formula CnH2n+2. They generally have from 5 to 40 carbon atoms per molecule, although trace amounts of shorter or longer molecules may be present in the mixture.

The alkanes from pentane (C5H12) to octane (C8H18) are refined into petrol, the ones from nonane (C9H20) to hexadecane (C16H34) into diesel fuel, kerosene and jet fuel. Alkanes with more than 16 carbon atoms can be refined into fuel oil and lubricating oil. At the heavier end of the range, paraffin wax is an alkane with approximately 25 carbon atoms, while asphalt has 35 and up, although these are usually cracked by modern refineries into more valuable products. The shortest molecules, those with four or fewer carbon atoms, are in a gaseous state at room temperature. They are the petroleum gases. Depending on demand and the cost of recovery, these gases are either flared off, sold as liquified petroleum gas under pressure, or used to power the refinery's own burners. During the winter, butane (C4H10), is blended into the petrol pool at high rates, because its high vapor pressure assists with cold starts. Liquified under pressure slightly above atmospheric, it is best known for powering cigarette lighters, but it is also a main fuel source for many developing countries. Propane can be liquified under modest pressure, and is consumed for just about every application relying on petroleum for energy, from cooking to heating to transportation.

The cycloalkanes, also known as naphthenes, are saturated hydrocarbons which have one or more carbon rings to which hydrogen atoms are attached according to the formula CnH2n. Cycloalkanes have similar properties to alkanes but have higher boiling points.

The aromatic hydrocarbons are unsaturated hydrocarbons which have one or more planar six-carbon rings called benzene rings, to which hydrogen atoms are attached with the formula CnHn. They tend to burn with a sooty flame, and many have a sweet aroma. Some are carcinogenic.

These different molecules are separated by fractional distillation at an oil refinery to produce petrol, jet fuel, kerosene, and other hydrocarbons. For example, 2,2,4-trimethylpentane (isooctane), widely used in petrol, has a chemical formula of C8H18 and it reacts with oxygen exothermically:[39]

C
8
H
18
(l) + 25 O
2
(g) → 16 CO
2
(g) + 18 H
2
O
(g) (ΔH = −5.51 MJ/mol of octane)

The number of various molecules in an oil sample can be determined in laboratory. The molecules are typically extracted in a solvent, then separated in a gas chromatograph, and finally determined with a suitable detector, such as a flame ionization detector or a mass spectrometer.[40] Due to the large number of co-eluted hydrocarbons within oil, many cannot be resolved by traditional gas chromatography and typically appear as a hump in the chromatogram. This unresolved complex mixture (UCM) of hydrocarbons is particularly apparent when analysing weathered oils and extracts from tissues of organisms exposed to oil.

Incomplete combustion of petroleum or petrol results in production of toxic byproducts. Too little oxygen results in carbon monoxide. Due to the high temperatures and high pressures involved, exhaust gases from petrol combustion in car engines usually include nitrogen oxides which are responsible for creation of photochemical smog.

Empirical equations for thermal properties[edit]

Heat of combustion[edit]

At a constant volume the heat of combustion of a petroleum product can be approximated as follows:

Q_v = 12400, - 2,100d^2.

where Q_v is measured in cal/gram and d is the specific gravity at 60 °F (16 °C).

Thermal conductivity[edit]

The thermal conductivity of petroleum based liquids can be modeled as follows:[41]

K = \frac{1.62}{d}[1-0.0003(t-32)]

where K is measured in BTU · in · F−1hr−1ft−2 , t is measured in F and d is the specific gravity at 60 °F (16 °C).

Specific heat[edit]

The specific heat of a petroleum oils can be modeled as follows:[42]

c = \frac{1}{d} [0.388+0.00046t],

where c is measured in BTU/lbm-°F, t is the temperature in Fahrenheit and d is the specific gravity at 60 °F (16 °C).

In units of kcal/(kg·°C), the formula is:

c = \frac{1}{d} [0.4024+0.00081t],

where the temperature t is in Celsius and d is the specific gravity at 15 °C.

Latent heat of vaporization[edit]

The latent heat of vaporization can be modeled under atmospheric conditions as follows:

L = \frac{1}{d}[110.9 - 0.09t],

where L is measured in BTU/lbm, t is measured in °F and d is the specific gravity at 60 °F (16 °C).

In units of kcal/kg, the formula is:

L = \frac{1}{d}[194.4 - 0.162t],

where the temperature t is in Celsius and d is the specific gravity at 15 °C.[43]

Formation[edit]

Structure of a vanadium porphyrin compound (left) extracted from petroleum by Alfred E. Treibs, father of organic geochemistry. Treibs noted the close structural similarity of this molecule and chlorophyll a (right).[44][45]

Petroleum is a fossil fuel derived from ancient fossilized organic materials, such as zooplankton and algae.[46] Vast quantities of these remains settled to sea or lake bottoms, mixing with sediments and being buried under anoxic conditions. As further layers settled to the sea or lake bed, intense heat and pressure built up in the lower regions. This process caused the organic matter to change, first into a waxy material known as kerogen, which is found in various oil shales around the world, and then with more heat into liquid and gaseous hydrocarbons via a process known as catagenesis. Formation of petroleum occurs from hydrocarbon pyrolysis in a variety of mainly endothermic reactions at high temperature and/or pressure.[47]

There were certain warm nutrient-rich environments such as the Gulf of Mexico and the ancient Tethys Sea where the large amounts of organic material falling to the ocean floor exceeded the rate at which it could decompose. This resulted in large masses of organic material being buried under subsequent deposits such as shale formed from mud. This massive organic deposit later became heated and transformed under pressure into oil.[48]

Geologists often refer to the temperature range in which oil forms as an "oil window"[49]—below the minimum temperature oil remains trapped in the form of kerogen, and above the maximum temperature the oil is converted to natural gas through the process of thermal cracking. Sometimes, oil formed at extreme depths may migrate and become trapped at a much shallower level. The Athabasca Oil Sands are one example of this.

An alternative mechanism was proposed by Russian scientists in the mid-1850s, the Abiogenic petroleum origin, but this is contradicted by the geological and geochemical evidence.[citation needed]

Reservoirs[edit]

Crude oil reservoirs[edit]

Hydrocarbon trap.

Three conditions must be present for oil reservoirs to form: a source rock rich in hydrocarbon material buried deep enough for subterranean heat to cook it into oil, a porous and permeable reservoir rock for it to accumulate in, and a cap rock (seal) or other mechanism that prevents it from escaping to the surface. Within these reservoirs, fluids will typically organize themselves like a three-layer cake with a layer of water below the oil layer and a layer of gas above it, although the different layers vary in size between reservoirs. Because most hydrocarbons are less dense than rock or water, they often migrate upward through adjacent rock layers until either reaching the surface or becoming trapped within porous rocks (known as reservoirs) by impermeable rocks above. However, the process is influenced by underground water flows, causing oil to migrate hundreds of kilometres horizontally or even short distances downward before becoming trapped in a reservoir. When hydrocarbons are concentrated in a trap, an oil field forms, from which the liquid can be extracted by drilling and pumping.

The reactions that produce oil and natural gas are often modeled as first order breakdown reactions, where hydrocarbons are broken down to oil and natural gas by a set of parallel reactions, and oil eventually breaks down to natural gas by another set of reactions. The latter set is regularly used in petrochemical plants and oil refineries.

Wells are drilled into oil reservoirs to extract the crude oil. "Natural lift" production methods that rely on the natural reservoir pressure to force the oil to the surface are usually sufficient for a while after reservoirs are first tapped. In some reservoirs, such as in the Middle East, the natural pressure is sufficient over a long time. The natural pressure in most reservoirs, however, eventually dissipates. Then the oil must be extracted using "artificial lift" means. Over time, these "primary" methods become less effective and "secondary" production methods may be used. A common secondary method is "waterflood" or injection of water into the reservoir to increase pressure and force the oil to the drilled shaft or "wellbore." Eventually "tertiary" or "enhanced" oil recovery methods may be used to increase the oil's flow characteristics by injecting steam, carbon dioxide and other gases or chemicals into the reservoir. In the United States, primary production methods account for less than 40 percent of the oil produced on a daily basis, secondary methods account for about half, and tertiary recovery the remaining 10 percent. Extracting oil (or "bitumen") from oil/tar sand and oil shale deposits requires mining the sand or shale and heating it in a vessel or retort, or using "in-situ" methods of injecting heated liquids into the deposit and then pumping out the oil-saturated liquid.

Unconventional oil reservoirs[edit]

Oil-eating bacteria biodegrade oil that has escaped to the surface. Oil sands are reservoirs of partially biodegraded oil still in the process of escaping and being biodegraded, but they contain so much migrating oil that, although most of it has escaped, vast amounts are still present—more than can be found in conventional oil reservoirs. The lighter fractions of the crude oil are destroyed first, resulting in reservoirs containing an extremely heavy form of crude oil, called crude bitumen in Canada, or extra-heavy crude oil in Venezuela. These two countries have the world's largest deposits of oil sands.

On the other hand, oil shales are source rocks that have not been exposed to heat or pressure long enough to convert their trapped hydrocarbons into crude oil. Technically speaking, oil shales are not always shales and do not contain oil, but are fined-grain sedimentary rocks containing an insoluble organic solid called kerogen. The kerogen in the rock can be converted into crude oil using heat and pressure to simulate natural processes. The method has been known for centuries and was patented in 1694 under British Crown Patent No. 330 covering, "A way to extract and make great quantities of pitch, tar, and oil out of a sort of stone." Although oil shales are found in many countries, the United States has the world's largest deposits.[50]

Classification[edit]

Some marker crudes with their sulfur content (horizontal) and API gravity (vertical) and relative production quantity.

The petroleum industry generally classifies crude oil by the geographic location it is produced in (e.g. West Texas Intermediate, Brent, or Oman), its API gravity (an oil industry measure of density), and its sulfur content. Crude oil may be considered light if it has low density or heavy if it has high density; and it may be referred to as sweet if it contains relatively little sulfur or sour if it contains substantial amounts of sulfur.

The geographic location is important because it affects transportation costs to the refinery. Light crude oil is more desirable than heavy oil since it produces a higher yield of petrol, while sweet oil commands a higher price than sour oil because it has fewer environmental problems and requires less refining to meet sulfur standards imposed on fuels in consuming countries. Each crude oil has unique molecular characteristics which are understood by the use of crude oil assay analysis in petroleum laboratories.

Barrels from an area in which the crude oil's molecular characteristics have been determined and the oil has been classified are used as pricing references throughout the world. Some of the common reference crudes are:

There are declining amounts of these benchmark oils being produced each year, so other oils are more commonly what is actually delivered. While the reference price may be for West Texas Intermediate delivered at Cushing, the actual oil being traded may be a discounted Canadian heavy oil delivered at Hardisty, Alberta, and for a Brent Blend delivered at Shetland, it may be a Russian Export Blend delivered at the port of Primorsk.[52]

Petroleum industry[edit]

New York Mercantile Exchange prices for West Texas Intermediate since 2000

The petroleum industry is involved in the global processes of exploration, extraction, refining, transporting (often with oil tankers and pipelines), and marketing petroleum products. The largest volume products of the industry are fuel oil and petrol. Petroleum is also the raw material for many chemical products, including pharmaceuticals, solvents, fertilizers, pesticides, and plastics. The industry is usually divided into three major components: upstream, midstream and downstream. Midstream operations are usually included in the downstream category.

Petroleum is vital to many industries, and is of importance to the maintenance of industrialized civilization itself, and thus is a critical concern to many nations. Oil accounts for a large percentage of the world's energy consumption, ranging from a low of 32 percent for Europe and Asia, up to a high of 53 percent for the Middle East, South and Central America (44%), Africa (41%), and North America (40%). The world at large consumes 30 billion barrels (4.8 km³) of oil per year, and the top oil consumers largely consist of developed nations. In fact, 24 percent of the oil consumed in 2004 went to the United States alone,[53] though by 2007 this had dropped to 21 percent of world oil consumed.[54]

In the US, in the states of Arizona, California, Hawaii, Nevada, Oregon and Washington, the Western States Petroleum Association (WSPA) represents companies responsible for producing, distributing, refining, transporting and marketing petroleum. This non-profit trade association was founded in 1907, and is the oldest petroleum trade association in the United States.[55]

Shipping[edit]

In the 1950s, shipping costs made up 33 percent of the price of oil transported from the Persian Gulf to USA,[56] but due to the development of supertankers in the 1970s, the cost of shipping dropped to only 5 percent of the price of Persian oil in USA.[56] Due to the increase of the value of the crude oil during the last 30 years, the share of the shipping cost on the final cost of the delivered commodity was less than 3% in 2010. For example, in 2010 the shipping cost from the Persian Gulf to the USA was in the range of 20 $/t and the cost of the delivered crude oil around 800 $/t.[citation needed]

Price[edit]

After the collapse of the OPEC-administered pricing system in 1985, and a short lived experiment with netback pricing, oil-exporting countries adopted a market-linked pricing mechanism.[57] First adopted by PEMEX in 1986, market-linked pricing was widely accepted, and by 1988 became and still is the main method for pricing crude oil in international trade.[57] The current reference, or pricing markers, are Brent, WTI, and Dubai/Oman.[57]

Uses[edit]

The chemical structure of petroleum is heterogeneous, composed of hydrocarbon chains of different lengths. Because of this, petroleum may be taken to oil refineries and the hydrocarbon chemicals separated by distillation and treated by other chemical processes, to be used for a variety of purposes. See Petroleum products.

Fuels[edit]

A poster used to promote carpooling as a way to ration gasoline during World War II.

The most common distillation fractions of petroleum are fuels. Fuels include (by increasing boiling temperature range):[58]

Common fractions of petroleum as fuels
FractionBoiling range oC
Liquefied petroleum gas (LPG)−40
Butane−12 to −1
Petrol−1 to 110
Jet fuel150 to 205
Kerosene205 to 260
Fuel oil205 to 290
Diesel fuel260 to 315

Other derivatives[edit]

Certain types of resultant hydrocarbons may be mixed with other non-hydrocarbons, to create other end products:

Agriculture[edit]

Since the 1940s, agricultural productivity has increased dramatically, due largely to the increased use of energy-intensive mechanization, fertilizers and pesticides.

Petroleum by country[edit]

Consumption statistics[edit]

Consumption[edit]

According to the US Energy Information Administration (EIA) estimate for 2011, the world consumes 87.421 million barrels of oil each day.

Oil consumption per capita (darker colors represent more consumption, gray represents no data).

This table orders the amount of petroleum consumed in 2011 in thousand barrels (1000 bbl) per day and in thousand cubic metres (1000 m3) per day:[60][61][62]

Consuming Nation 2011(1000 bbl/
day)
(1000 m3/
day)
population
in millions
bbl/year
per capita
m3/year
per capita
national production/
consumption
United States 118,835.52,994.631421.83.470.51
China9,790.01,556.513452.70.430.41
Japan 24,464.1709.712712.82.040.03
India 23,292.2523.4119810.160.26
Russia 13,145.1500.01408.11.293.35
Saudi Arabia (OPEC)2,817.5447.927406.43.64
Brazil2,594.2412.41934.90.780.99
Germany 22,400.1381.68210.71.700.06
Canada2,259.1359.23324.63.911.54
South Korea 22,230.2354.64816.82.670.02
Mexico 12,132.7339.11097.11.131.39
France 21,791.5284.86210.51.670.03
Iran (OPEC)1,694.4269.4748.31.322.54
United Kingdom 11,607.9255.6619.51.510.93
Italy 21,453.6231.1608.91.410.10

Source: US Energy Information Administration

Population Data:[63]

1 peak production of oil already passed in this state

2 This country is not a major oil producer

Production[edit]

Oil producing countries
Graph of Top Oil Producing Countries 1960–2006, including Soviet Union[64]

In petroleum industry parlance, production refers to the quantity of crude extracted from reserves, not the literal creation of the product.

#Producing Nation103bbl/d (2006)103bbl/d (2007)103bbl/d (2008)103bbl/d (2009)Present Share
1Saudi Arabia (OPEC)10,66510,23410,7829,76011.8%
2Russia 19,6779,8769,7899,93412.0%
3United States 18,3318,4818,5149,14111.1%
4Iran (OPEC)4,1484,0434,1744,1775.1%
5China3,8463,9013,9733,9964.8%
6Canada 23,2883,3583,3503,2944.0%
7Mexico 13,7073,5013,1853,0013.6%
8United Arab Emirates (OPEC)2,9452,9483,0462,7953.4%
9Kuwait (OPEC)2,6752,6132,7422,4963.0%
10Venezuela (OPEC) 12,8032,6672,6432,4713.0%
11Norway 12,7862,5652,4662,3502.8%
12Brazil2,1662,2792,4012,5773.1%
13Iraq (OPEC) 32,0082,0942,3852,4002.9%
14Algeria (OPEC)2,1222,1732,1792,1262.6%
15Nigeria (OPEC)2,4432,3522,1692,2112.7%
16Angola (OPEC)1,4351,7692,0141,9482.4%
17Libya (OPEC)1,8091,8451,8751,7892.2%
18United Kingdom1,6891,6901,5841,4221.7%
19Kazakhstan1,3881,4451,4291,5401.9%
20Qatar (OPEC)1,1411,1361,2071,2131.5%
21Indonesia1,1021,0441,0511,0231.2%
22India8548818848771.1%
23Azerbaijan6488508751,0121.2%
24Argentina8027917927941.0%
25Oman7437147618161.0%
26Malaysia7297037276930.8%
27Egypt6676646316780.8%
28Colombia5445436016860.8%
29Australia5525955865880.7%
30Ecuador (OPEC)5365125054850.6%
31Sudan3804664804860.6%
32Syria4494464264000.5%
33Equatorial Guinea3864003593460.4%
34Thailand3343493613390.4%
35Vietnam3623523143460.4%
36Yemen3773613002870.3%
37Denmark3443142892620.3%
38Gabon2372442482420.3%
39South Africa2041991951920.2%
40TurkmenistanNo data1801891980.2%
41Trinidad and Tobago1811791761740.1%

Source: U.S. Energy Information Administration

1 Peak production of conventional oil already passed in this state

2 Although Canada's conventional oil production is declining, its total oil production is increasing as oil sands production grows. When oil sands are included, Canada has the world's second largest oil reserves after Saudi Arabia.

3 Trinidad and Tobago has the worlds third largest pitch lake situated La Brea south Trinidad

4 Though still a member, Iraq has not been included in production figures since 1998

In 2013, the United States will produce an average of 11.4 million barrels a day, which would make it the second largest producer of hydrocarbons,[65] and is expected to overtake Saudi Arabia before 2020.[66]

Export[edit]

Oil exports by country.

In order of net exports in 2011, 2009 and 2006 in thousand bbl/d and thousand m³/d:

#Exporting Nation103bbl/d (2011)103m3/d (2011)103bbl/d (2009)103m3/d (2009)103bbl/d (2006)103m3/d (2006)
1Saudi Arabia (OPEC)8,3361,3257,3221,1648,6511,376
2Russia 17,0831,1267,1941,1446,5651,044
3Iran (OPEC)2,5404032,4863952,519401
4United Arab Emirates (OPEC)2,5244012,3033662,515400
5Kuwait (OPEC)2,3433732,1243382,150342
6Nigeria (OPEC)2,2573591,9393082,146341
7Iraq (OPEC)1,9153041,7642801,438229
8Angola (OPEC)1,7602801,8782991,363217
9Norway 11,7522792,1323392,542404
10Venezuela (OPEC) 11,7152731,7482782,203350
11Algeria (OPEC) 11,5682491,7672811,847297
12Qatar (OPEC)1,4682331,066169
13Canada 21,4052231,1681871,071170
14Kazakhstan1,3962221,2992071,114177
15Azerbaijan 183613391214553285
16Trinidad and Tobago 1177112167160155199

Source: US Energy Information Administration

1 peak production already passed in this state

2 Canadian statistics are complicated by the fact it is both an importer and exporter of crude oil, and refines large amounts of oil for the U.S. market. It is the leading source of U.S. imports of oil and products, averaging 2,500,000 bbl/d (400,000 m3/d) in August 2007. [1].

Total world production/consumption (as of 2005) is approximately 84 million barrels per day (13,400,000 m3/d).

Import[edit]

Oil imports by country.

In order of net imports in 2011, 2009 and 2006 in thousand bbl/d and thousand m³/d:

#Importing Nation103bbl/day (2011)103m3/day (2011)103bbl/day (2009)103m3/day (2009)103bbl/day (2006)103m3/day (2006)
1United States 18,7281,3889,6311,53112,2201,943
2China 25,4878724,3286883,438547
3Japan4,3296884,2356735,097810
4India2,3493732,2333551,687268
5Germany2,2353552,3233692,483395
6South Korea2,1703452,1393402,150342
7France1,6972701,7492781,893301
8Spain1,3462141,4392291,555247
9Italy1,2922051,3812201,558248
10Singapore1,172186916146787125
11Republic of China (Taiwan)1,009160944150942150
12Netherlands948151973155936149
13Turkey65010365010357692
14Belgium6341015979554687
15Thailand592945388660696

Source: US Energy Information Administration

1 peak production of oil expected in 2020[67]

2 Major oil producer whose production is still increasing[citation needed]

Import to the USA by country 2010[edit]

oil imports to US 2010

Non-producing consumers[edit]

Countries whose oil production is 10% or less of their consumption.

#Consuming Nation(bbl/day)(m³/day)
1Japan5,578,000886,831
2Germany2,677,000425,609
3South Korea2,061,000327,673
4France2,060,000327,514
5Italy1,874,000297,942
6Spain1,537,000244,363
7Netherlands946,700150,513
8Turkey575,01191,663

Source: CIA World Factbook[not in citation given]

Environmental effects[edit]

Diesel fuel spill on a road

Because petroleum is a naturally occurring substance, its presence in the environment need not be the result of human causes such as accidents and routine activities (seismic exploration, drilling, extraction, refining and combustion). Phenomena such as seeps[68] and tar pits are examples of areas that petroleum affects without man's involvement. Regardless of source, petroleum's effects when released into the environment are similar.

Global warming[edit]

When burned, petroleum releases carbon dioxide; a greenhouse gas. Along with the burning of coal, petroleum combustion is the largest contributor to the increase in atmospheric CO2. Atmospheric CO2 has risen steadily since the industrial revolution to current levels of over 390 ppmv, from the 180 – 300 ppmv of the prior 800 thousand years, driving global warming.[69][70][71] The unbridled use of petroleum could potentially cause a runaway greenhouse effect on Earth.[citation needed] Use of oil as an energy source has caused Earth's temperature to increase by nearly one degree Celsius. This raise in temperature has reduced the Arctic ice cap to 1,100,000 sq mi (2,800,000 km2), smaller than ever recorded.[72] Because of this melt, more oil reserves have been revealed. It is estimated by the International Energy Agency that about 13 percent of the world's undiscovered oil resides in the Arctic.[73]

Extraction[edit]

Oil extraction is simply the removal of oil from the reservoir (oil pool). Oil is often recovered as a water-in-oil emulsion, and specialty chemicals called demulsifiers are used to separate the oil from water. Oil extraction is costly and sometimes environmentally damaging, although Dr. John Hunt of the Woods Hole Oceanographic Institution pointed out in a 1981 paper that over 70 percent of the reserves in the world are associated with visible macroseepages, and many oil fields are found due to natural seeps. Offshore exploration and extraction of oil disturbs the surrounding marine environment.[74]

Oil spills[edit]

Kelp after an oil spill
Oil Sick from the Montara oil spill in the Timor Sea, September, 2009
Volunteers cleaning up the aftermath of the Prestige oil spill

Crude oil and refined fuel spills from tanker ship accidents have damaged natural ecosystems in Alaska, the Gulf of Mexico, the Galapagos Islands, France and many other places.

The quantity of oil spilled during accidents has ranged from a few hundred tons to several hundred thousand tons (e.g., Deepwater Horizon Oil Spill, Atlantic Empress, Amoco Cadiz). Smaller spills have already proven to have a great impact on ecosystems, such as the Exxon Valdez oil spill

Oil spills at sea are generally much more damaging than those on land, since they can spread for hundreds of nautical miles in a thin oil slick which can cover beaches with a thin coating of oil. This can kill sea birds, mammals, shellfish and other organisms it coats. Oil spills on land are more readily containable if a makeshift earth dam can be rapidly bulldozed around the spill site before most of the oil escapes, and land animals can avoid the oil more easily.

Control of oil spills is difficult, requires ad hoc methods, and often a large amount of manpower. The dropping of bombs and incendiary devices from aircraft on SS Torrey Canyon wreck produced poor results;[75] modern techniques would include pumping the oil from the wreck, like in the Prestige oil spill or the Erika oil spill.[76]

Though crude oil is predominantly composed of various hydrocarbons, certain nitrogen heterocylic compounds, such as pyridine, picoline, and quinoline are reported as contaminants associated with crude oil, as well as facilities processing oil shale or coal, and have also been found at legacy wood treatment sites. These compounds have a very high water solubility, and thus tend to dissolve and move with water. Certain naturally occurring bacteria, such as Micrococcus, Arthrobacter, and Rhodococcus have been shown to degrade these contaminants.[77]

Tarballs[edit]

A tarball is a blob of crude oil (not to be confused with tar, which is typically derived from pine trees rather than petroleum) which has been weathered after floating in the ocean. Tarballs are an aquatic pollutant in most environments, although they can occur naturally, for example, in the Santa Barbara Channel of California.[78][79] Their concentration and features have been used to assess the extent of oil spills. Their composition can be used to identify their sources of origin,[80][81] and tarballs themselves may be dispersed over long distances by deep sea currents.[79] They are slowly decomposed by bacteria, including Chromobacterium violaceum, Cladosporium resinae, Bacillus submarinus, Micrococcus varians, Pseudomonas aeruginosa, Candida marina and Saccharomyces estuari.[78]

Whales[edit]

James S. Robbins has argued that the advent of petroleum-refined kerosene saved some species of great whales from extinction by providing an inexpensive substitute for whale oil, thus eliminating the economic imperative for open-boat whaling.[82]

Alternatives to petroleum[edit]

In the United States in 2007 about 70 percent of petroleum was used for transportation (e.g. petrol, diesel, jet fuel), 24 percent by industry (e.g. production of plastics), 5 percent for residential and commercial uses, and 2 percent for electricity production.[83] Outside of the US, a higher proportion of petroleum tends to be used for electricity.[84]

Alternatives to petroleum-based vehicle fuels[edit]

Typical Brazilian fuel station with four alternative fuels for sale: diesel (B3), gasohol (E25), neat ethanol (E100), and compressed natural gas (CNG).

Alternative fuel vehicles refers to both:

Alternatives to using oil in industry[edit]

Biological feedstocks do exist for industrial uses such as Bioplastic production.[85]

Alternatives to burning petroleum for electricity[edit]

In oil producing countries with little refinery capacity, oil is sometimes burned to produce electricity. Renewable energy technologies such as solar power, wind power, micro hydro, biomass and biofuels are used, but the primary alternatives remain large-scale hydroelectricity, nuclear and coal-fired generation.

Future of petroleum production[edit]

US oil production and imports, 1910-2012.

Consumption in the twentieth and twenty-first centuries has been abundantly pushed by automobile growth; the 1985–2003 oil glut even fueled the sales of low economy vehicles in OECD countries. The 2008 economic crisis seems to have had some impact on the sales of such vehicles; still, the 2008 oil consumption shows a small increase. The BRIC countries might also kick in, as China briefly was the first automobile market in December 2009.[86] The immediate outlook still hints upwards. In the long term, uncertainties linger; the OPEC believes that the OECD countries will push low consumption policies at some point in the future; when that happens, it will definitely curb oil sales, and both OPEC and EIA kept lowering their 2020 consumption estimates during the past 5 years.[87] Oil products are more and more in competition with alternative sources, mainly coal and natural gas, both cheaper sources. Production will also face an increasingly complex situation; while OPEC countries still have large reserves at low production prices, newly found reservoirs often lead to higher prices; offshore giants such as Tupi, Guara and Tiber demand high investments and ever-increasing technological abilities. Subsalt reservoirs such as Tupi were unknown in the twentieth century, mainly because the industry was unable to probe them. Enhanced Oil Recovery (EOR) techniques (example: DaQing, China[88] ) will continue to play a major role in increasing the world's recoverable oil.

Peak oil[edit]

Global Peak Oil forecast

Peak oil is the projection that future petroleum production (whether for individual oil wells, entire oil fields, whole countries, or worldwide production) will eventually peak and then decline at a similar rate to the rate of increase before the peak as these reserves are exhausted. The peak of oil discoveries was in 1965, and oil production per year has surpassed oil discoveries every year since 1980.[89]

Hubbert applied his theory to accurately predict the peak of U.S. oil production at a date between 1966 and 1970. This prediction was based on data available at the time of his publication in 1956. In the same paper, Hubbert predicts world peak oil in "half a century" after his publication, which would be 2006.[90]

It is difficult to predict the oil peak in any given region, due to the lack of knowledge and/or transparency in accounting of global oil reserves.[91] Based on available production data, proponents have previously predicted the peak for the world to be in years 1989, 1995, or 1995–2000. Some of these predictions date from before the recession of the early 1980s, and the consequent reduction in global consumption, the effect of which was to delay the date of any peak by several years. Just as the 1971 U.S. peak in oil production was only clearly recognized after the fact, a peak in world production will be difficult to discern until production clearly drops off.[92] The peak is also a moving target as it is now measured as "liquids", which includes synthetic fuels, instead of just conventional oil.[93]

The International Energy Agency (IEA) said in 2010 that production of conventional crude oil had peaked in 2006 at 70 MBBL/d, then flattened at 68 or 69 thereafter.[94][95] Since virtually all economic sectors rely heavily on petroleum, peak oil, if it were to occur, could lead to a "partial or complete failure of markets".[96]

See also[edit]

Notes[edit]

  1. ^ "Petroleum". Concise Oxford English Dictionary
  2. ^ The Latin word petra is a loanword from Greek πέτρα.
  3. ^ "Gasoline as Fuel – History of Word Gasoline – Gasoline and Petroleum Origins". Alternativefuels.about.com. 2013-07-12. Retrieved 2013-08-27. 
  4. ^ EIA Energy Kids - Oil (petroleum). Eia.gov. Retrieved on 2013-11-26.
  5. ^ Guerriero V. et al. (2012). "A permeability model for naturally fractured carbonate reservoirs". Marine and Petroleum Geology (Elsevier) 40: 115–134. doi:10.1016/j.marpetgeo.2012.11.002. 
  6. ^ Guerriero V. et al. (2011). "Improved statistical multi-scale analysis of fractures in carbonate reservoir analogues". Tectonophysics (Elsevier) 504: 14–24. Bibcode:2011Tectp.504...14G. doi:10.1016/j.tecto.2011.01.003. 
  7. ^ "Organic Hydrocarbons: Compounds made from carbon and hydrogen". Archived from the original on July 19, 2011. 
  8. ^ "Libyan tremors threaten to rattle the oil world". The Hindu (Chennai, India). March 1, 2011. 
  9. ^ Oxford English Dictionary online edition, entry "petroleum"
  10. ^ Bauer (1546)
  11. ^ Public Domain One or more of the preceding sentences incorporates text from a publication now in the public domainChisholm, Hugh, ed. (1911). "Petroleum". Encyclopædia Britannica (11th ed.). Cambridge University Press. 
  12. ^ George E. Totten ASTM Timeline
  13. ^ Longmuir, Marilyn V. "Oil in Burma: The Extraction of "Earth Oil" to 1914". Bangkok: White Lotus (2001) ISBN 974-7534-60-6 pp.329
  14. ^ Russell, Loris S. (2003). A Heritage of Light: Lamps and Lighting in the Early Canadian Home. University of Toronto Press. ISBN 0-8020-3765-8. 
  15. ^ "James Young". 
  16. ^ Maugeri (2006), p. 3
  17. ^ Vassiliou, M. S. (2009). Historical Dictionary of the Petroleum Industry. Lanham, MD: Scarecrow Press (Rowman & Littlefield), 700pp
  18. ^ Matveichuk, Alexander A. Intersection of Oil Parallels: Historical Essays. Moscow: Russian Oil and Gas Institute, 2004.
  19. ^ McKain, David L., and Bernard L. Allen. Where It All Began: The Story of the People and Places Where the Oil Industry Began—West Virginia and South- eastern Ohio. Parkersburg, W.Va.: David L. McKain, 1994.
  20. ^ The History Of Romanian Oil Industry
  21. ^ PBS: World Events
  22. ^ a b c http://www.lclmg.org/lclmg/Museums/OilMuseumofCanada/BlackGold2/OilHeritage/OilSprings/tabid/208/Default.aspx Oil Museum of Canada, Black Gold: Canada's Oil Heritage, Oil Springs: Boom & Bust
  23. ^ Turnbull Elford, Jean. Canada West's Last Frontier. Lambton County Historical Society, 1982, p. 110
  24. ^ May, Gary. Hard Oiler! The Story of Early Canadians' Quest for Oil at Home and Abroad. Dundurn Press, 1998, p 43
  25. ^ Ford, R. W. A History of the Chemical Industry in Lambton County, 1988, p 5
  26. ^ Akiner(2004), p. 5
  27. ^ Hanson Baldwin, 1959, "Oil Strategy in World War II", American Petroleum Institute Quarterly – Centennial Issue, pages 10–11. American Petroleum Institute.
  28. ^ Baku: City that Oil Built Archived 11 February 2011 at WebCite
  29. ^ "InfoPlease". InfoPlease. Retrieved August 29, 2010. 
  30. ^ a b Hyne (2001), pp. 1–4.
  31. ^ Speight (1999), p. 215–216.
  32. ^ Alboudwarej et al. (Summer 2006). Highlighting Heavy Oil (PDF). Oilfield Review. Retrieved July 4, 2012. 
  33. ^ "Oil Sands – Glossary". Mines and Minerals Act. Government of Alberta. 2007. Archived from the original on November 1, 2007. Retrieved October 2, 2008. 
  34. ^ "Oil Sands in Canada and Venezuela". Infomine Inc. 2008. Retrieved October 2, 2008. 
  35. ^ IEA Key World Energy Statistics[dead link]
  36. ^ "Crude oil is made into different fuels". Eia.doe.gov. Retrieved August 29, 2010. 
  37. ^ "EIA reserves estimates". Eia.doe.gov. Retrieved August 29, 2010. 
  38. ^ "CERA report on total world oil". Cera.com. November 14, 2006. Retrieved August 29, 2010. 
  39. ^ "Heat of Combustion of Fuels". Webmo.net. Retrieved August 29, 2010. 
  40. ^ Use of ozone depleting substances in laboratories. TemaNord 2003:516.
  41. ^ http://www.osti.gov/scitech/servlets/purl/446318
  42. ^ Speight (2007), p. 25.
  43. ^ United States Bureau of Standards, "Thermal Properties of Petroleum Products". Miscellaneous Publication No. 97, November 9, 1929.
  44. ^ Treibs, A.E. (1936). "Chlorophyll- und Häminderivate in organischen Mineralstoffen". Angew. Chem. 49 (38): 682–686. doi:10.1002/ange.19360493803. 
  45. ^ Kvenvolden, K. A. (2006). "Organic geochemistry – A retrospective of its first 70 years". Org. Geochem. 37: 1–11. doi:10.1016/j.orggeochem.2005.09.001. 
  46. ^ Kvenvolden, Keith A. (2006). "Organic geochemistry – A retrospective of its first 70 years". Organic Geochemistry 37: 1. doi:10.1016/j.orggeochem.2005.09.001. 
  47. ^ Braun, Robert L.; Burnham, lan K. (June 1993). "Chemical Reaction Model for Oil and Gas Generation from Type I and Type II Kerogen". Lawrence Livermore National Laboratory. Retrieved August 29, 2010. 
  48. ^ Broad, William J. (August 2, 2010). "Tracing Oil Reserves to Their Tiny Origins". The New York Times. Retrieved August 2, 2010. 
  49. ^ Polar Prospects:A minerals treaty for Antarctica. United States, Office of Technology Assessment. September 1989. p. 104. ISBN 978-1-4289-2232-7. 
  50. ^ Lambertson, Giles (February 16, 2008). "Oil Shale: Ready to Unlock the Rock". Construction Equipment Guide. Retrieved May 21, 2008. 
  51. ^ "Chevron Crude Oil Marketing – North America Posted Pricing – California". Crudemarketing.chevron.com. May 1, 2007. Retrieved August 29, 2010. 
  52. ^ "Light Sweet Crude Oil". About the Exchange. New York Mercantile Exchange (NYMEX). 2006. Archived from the original on March 14, 2008. Retrieved April 21, 2008. 
  53. ^ "International Energy Annual 2004" (XLS). Energy Information Administration. July 14, 2006. 
  54. ^ "Yearbook 2008 – crude oil". Energy data. 
  55. ^ "About Us". Western States Petroleum Association. Archived from the original on June 16, 2008. Retrieved November 3, 2008. 
  56. ^ a b "A liquid market: Thanks to LNG, spare gas can now be sold the world over". The Economist. 14 July 2012. Retrieved 6 January 2013. 
  57. ^ a b c Mabro (2006), p. 351.
  58. ^ Speight (1999), p. 543.
  59. ^ BP: Statistical Review of World Energy, Workbook (xlsx), London, 2012
  60. ^ U.S. Energy Information Administration. Excel file from this web page. Table Posted: March 1, 2010
  61. ^ From DSW-Datareport 2008 ("Deutsche Stiftung Weltbevölkerung")
  62. ^ One cubic metre of oil is equivalent to 6.28981077 barrels of oil
  63. ^ "IBGE". IBGE. Retrieved August 29, 2010. 
  64. ^ "World Crude Oil Production" (PDF). Retrieved August 29, 2010. 
  65. ^ "U.S. may soonbecome world's top oil producer". CBS News. 23 October 2012. Retrieved 9 February 2013. 
  66. ^ Mark Thompson (12 November 2012). "U.S. to become biggest oil producer – IEA". CNN. Retrieved 9 February 2013. 
  67. ^ "AEO2014 EARLY RELEASE OVERVIEW" Early report US Energy Information Administration, December 2013. Accessed: December 2013. Quote: "Domestic production of crude oil .. increases sharply .. is expected to level off and then slowly decline after 2020"
  68. ^ http://seeps.wr.usgs.gov/ Natural Oil and Gas Seeps in California
  69. ^ Historical trends in carbon dioxide concentrations and temperature, on a geological and recent time scale. (June 2007). In UNEP/GRID-Arendal Maps and Graphics Library. Retrieved 19:14, February 19, 2011.
  70. ^ Deep ice tells long climate story. Retrieved 19:14, February 19, 2011.
  71. ^ Mitchell John F. B. (1989). "The "Greenhouse" Effect and Climate Change". Reviews of Geophysics 27 (1): 115–139. Bibcode:1989RvGeo..27..115M. doi:10.1029/RG027i001p00115. 
  72. ^ McKibbin, Bill. Eaarth: Making a Life on a Tough New Planet. New York: Times, 2010 ISBN 978-0312541194
  73. ^ "Arctic Sea Ice Reaches New Low, Shattering Record Set Just 3 Weeks Ago." NBCNews.com, 19 Sept. 2012. Web. 1 Oct. 2012. <http://worldnews.nbcnews.com>.
  74. ^ Waste discharges during the offshore oil and gas activity by Stanislave Patin, tr. Elena Cascio
  75. ^ Torrey Canyon bombing by the Navy and RAF
  76. ^ "Pumping of the Erika cargo". Total.com. Retrieved August 29, 2010. 
  77. ^ Sims, Gerald K.; O'Loughlin, Edward J.; Crawford, Ronald L. (1989). "Degradation of pyridines in the environment". Critical Reviews in Environmental Control (Taylor & Francis) 19 (4): 309–340. doi:10.1080/10643388909388372. 
  78. ^ a b Itah A. Y. and Essien J. P. (Oct 2005). "Growth Profile and Hydrocarbonoclastic Potential of Microorganisms Isolated from Tarballs in the Bight of Bonny, Nigeria". World Journal of Microbiology and Biotechnology (Kluwer Academic) 21 (6–7): 1317–1322. doi:10.1007/s11274-004-6694-z. 
  79. ^ a b Frances D. Hostettler, Robert J. Rosenbauer, Thomas D. Lorenson, Jennifer Dougherty, Geochemical characterization of tarballs on beaches along the California coast. Part I-- Shallow seepage impacting the Santa Barbara Channel Islands, Santa Cruz, Santa Rosa and San Miguel, Organic Geochemistry, Volume 35, Issue 6, June 2004, Pages 725–746, ISSN 0146-6380, doi:10.1016/j.orggeochem.2004.01.022.
  80. ^ Knap Anthony H, Burns Kathryn A, Dawson Rodger, Ehrhardt Manfred, and Palmork Karsten H (Dec 1984). "Dissolved/dispersed hydrocarbons, tarballs and the surface microlayer: Experiences from an IOC/UNEP Workshop in Bermuda". Marine Pollution Bulletin 17 (7): 313–319. doi:10.1016/0025-326X(86)90217-1. 
  81. ^ Zhendi Wang, Merv Fingas, Michael Landriault, Lise Sigouin, Bill Castle, David Hostetter, Dachung Zhang, Brad Spencer, "Identification and Linkage of Tarballs from the Coasts of Vancouver Island and Northern California Using GC/MS and Isotopic Techniques Journal of High Resolution Chromatography, Volume 21 Issue 7, Pages 383–395, doi:10.1002/(SICI)1521-4168(19980701)21:7<383::AID-JHRC383>3.0.CO;2–3
  82. ^ How Capitalism Saved the Whales by James S. Robbins, The Freeman, August, 1992.
  83. ^ "U.S. Primary Energy Consumption by Source and Sector, 2007". Energy Information Administration
  84. ^ needtitle UN Energy Program
  85. ^ Bioprocessing Seattle Times (2003)
  86. ^ Chris Hogg (February 10, 2009). "China's car industry overtakes US". BBC News. 
  87. ^ OPEC Secretariat (2008). "World Oil Outlook 2008". [dead link]
  88. ^ Ni Weiling (October 16, 2006). "Daqing Oilfield rejuvenated by virtue of technology". 
  89. ^ Campbell CJ (December 2000). "Peak Oil Presentation at the Technical University of Clausthal". 
  90. ^ Hubbert, Marion King; Shell Development Company (1956). "Nuclear energy and the fossil fuels". Drilling and Production Practice (Washington, DC: American Petroleum Institute) 95. 
  91. ^ "New study raises doubts about Saudi oil reserves". Iags.org. March 31, 2004. Retrieved August 29, 2010. 
  92. ^ Peak Oil Info and Strategies "The only uncertainty about peak oil is the time scale, which is difficult to predict accurately."
  93. ^ "Peak Oil": The Eventual End of the Oil Age pg. 12
  94. ^ "Is 'Peak Oil' Behind Us?". The New York Times. November 14, 2010
  95. ^ "Has the World Already Passed "Peak Oil"? ". National Geographic News. November 9, 2010
  96. ^ "Military Study Warns of a Potentially Drastic Oil Crisis". Spiegel Online. September 1, 2010.

References[edit]

Further reading[edit]

External links[edit]