From Wikipedia, the free encyclopedia - View original article
A pendulum clock is a clock that uses a pendulum, a swinging weight, as its timekeeping element. The advantage of a pendulum for timekeeping is that it is a harmonic oscillator; it swings back and forth in a precise time interval dependent on its length, and resists swinging at other rates. From its invention in 1656 by Christiaan Huygens until the 1930s, the pendulum clock was the world's most precise timekeeper, accounting for its widespread use. Throughout the 18th and 19th centuries pendulum clocks in homes, factories, offices and railroad stations served as primary time standards for scheduling daily life, work shifts, and public transportation, and their greater accuracy allowed the faster pace of life which was necessary for the Industrial Revolution.
Pendulum clocks must be stationary to operate; any motion or accelerations will affect the motion of the pendulum, causing inaccuracies, so other mechanisms must be used in portable timepieces. They are now kept mostly for their decorative and antique value.
The pendulum clock was invented in 1656 by Dutch scientist Christiaan Huygens, and patented the following year. Huygens contracted the construction of his clock designs to clockmaker Salomon Coster, who actually built the clock. Huygens was inspired by investigations of pendulums by Galileo Galilei beginning around 1602. Galileo discovered the key property that makes pendulums useful timekeepers: isochronism, which means that the period of swing of a pendulum is approximately the same for different sized swings. Galileo had the idea for a pendulum clock in 1637, which was partly constructed by his son in 1649, but neither lived to finish it. The introduction of the pendulum, the first harmonic oscillator used in timekeeping, increased the accuracy of clocks enormously, from about 15 minutes per day to 15 seconds per day leading to their rapid spread as existing 'verge and foliot' clocks were retrofitted with pendulums.
These early clocks, due to their verge escapements, had wide pendulum swings of up to 100°. In his 1673 analysis of pendulums, Horologium Oscillatorium, Huygens showed that wide swings made the pendulum inaccurate, causing its period, and thus the rate of the clock, to vary with unavoidable variations in the driving force provided by the movement. Clockmakers' realization that only pendulums with small swings of a few degrees are isochronous motivated the invention of the anchor escapement around 1670, which reduced the pendulum's swing to 4°-6°. The anchor became the standard escapement used in pendulum clocks. In addition to increased accuracy, the anchor's narrow pendulum swing allowed the clock's case to accommodate longer, slower pendulums, which needed less power and caused less wear on the movement. The seconds pendulum (also called the Royal pendulum), 0.994 m (39.1 in) long, in which each swing takes one second, became widely used in quality clocks. The long narrow clocks built around these pendulums, first made by William Clement around 1680, became known as grandfather clocks. The increased accuracy resulting from these developments caused the minute hand, previously rare, to be added to clock faces beginning around 1690.
The 18th and 19th century wave of horological innovation that followed the invention of the pendulum brought many improvements to pendulum clocks. The deadbeat escapement invented in 1675 by Richard Towneley and popularized by George Graham around 1715 in his precision "regulator" clocks gradually replaced the anchor escapement and is now used in most modern pendulum clocks. Observation that pendulum clocks slowed down in summer brought the realization that thermal expansion and contraction of the pendulum rod with changes in temperature was a source of error. This was solved by the invention of temperature-compensated pendulums; the mercury pendulum by George Graham in 1721 and the gridiron pendulum by John Harrison in 1726. With these improvements, by the mid-18th century precision pendulum clocks achieved accuracies of a few seconds per week.
Until the 19th century, clocks were handmade by individual craftsmen and were very expensive. The rich ornamentation of pendulum clocks of this period indicates their value as status symbols of the wealthy. The clockmakers of each country and region in Europe developed their own distinctive styles. By the 19th century, factory production of clock parts gradually made pendulum clocks affordable by middle-class families.
During the Industrial Revolution, daily life was organized around the home pendulum clock. More accurate pendulum clocks, called regulators, were installed in places of business and used to schedule work and set other clocks. The most accurate, known as astronomical regulators, were used in observatories for astronomy, surveying, and celestial navigation. Beginning in the 19th century, astronomical regulators in naval observatories served as primary standards for national time distribution services. From 1909, US National Bureau of Standards (now NIST) based the US time standard on Riefler pendulum clocks, accurate to about 10 milliseconds per day. In 1929 it switched to the Shortt-Synchronome free pendulum clock before phasing in quartz standards in the 1930s.  With an error of around one second per year, the Shortt was the most accurate commercially-produced pendulum clock.
Pendulum clocks remained the world standard for accurate timekeeping for 270 years, until the invention of the quartz clock in 1927, and were used as time standards through World War 2. The French Time Service used pendulum clocks as part of their ensemble of standard clocks until 1954  The home pendulum clock began to be replaced as domestic timekeeper during the 1930s and 1940s by the synchronous electric clock, which kept more accurate time because it was synchronized to the oscillation of the electric power grid. The most accurate experimental pendulum clock to date (2007) may be the Littlemore clock, built by Edward T. Hall in the 1990s  (donated in 2003 to the National Watch and Clock Museum, Columbia, USA).
All mechanical pendulum clocks have these five parts:
Additional functions in clocks besides basic timekeeping are called complications. More elaborate pendulum clocks may include these complications:
In electromechanical pendulum clocks such as used in mechanical Master clocks the power source is replaced by an electrically powered solenoid that provides the impulses to the pendulum by magnetic force, and the escapement is replaced by a switch or photodetector that senses when the pendulum is in the right position to receive the impulse. These should not be confused with more recent quartz pendulum clocks in which an electronic quartz clock module swings a pendulum. These are not true pendulum clocks because the timekeeping is controlled by a quartz crystal in the module, and the swinging pendulum is merely a decorative simulation.
The pendulum swings with a period that varies with the square root of its effective length. For small swings the period T in seconds, the time for one complete cycle (two swings), is
where L is the length of the pendulum in meters and g is the local acceleration of gravity in meters per second squared. All pendulum clocks have a means of adjusting the rate. This is usually an adjustment nut under the pendulum bob which moves the bob up or down on its rod. Moving the bob up reduces the length of the pendulum, reducing the pendulum's period so the clock gains time. In some pendulum clocks, fine adjustment is done with an auxiliary adjustment, which may be a small weight that is moved up or down the pendulum rod. In some master clocks and tower clocks, adjustment is accomplished by a small tray mounted on the rod where small weights are placed or removed to change the effective length, so the rate can be adjusted without stopping the clock.
The period of a pendulum increases slightly with the width (amplitude) of its swing. The rate of error increases with amplitude, so when limited to small swings of a few degrees the pendulum is nearly isochronous; its period is independent of changes in amplitude. Therefore the swing of the pendulum in clocks is limited to 2° to 4°.
One source of error in clocks is that the pendulum rod changes length slightly with changes in temperature. An increase in temperature causes the rod to expand, making the pendulum longer, so its period increases and the clock loses time. Wood expands less than metal, so many older quality clocks had wooden pendulum rods. To compensate for this expansion, early high-precision clocks used mercury pendulums, invented by George Graham in 1721. These had a bob consisting of a container of the liquid metal mercury. An increase in temperature would cause the rod to expand, but the mercury in the container would expand also and its level would rise slightly in the container, keeping the center of gravity of the pendulum at the same height.
The most widely used temperature compensated pendulum was the gridiron pendulum invented by John Harrison in 1726. This consisted of a "grid" of parallel rods of high-thermal-expansion metal such as zinc or brass and low-thermal-expansion metal such as steel mounted in a frame. It was constructed so that the high expansion rods compensated for the length change of the low-expansion rods, achieving zero length change with temperature changes. This type of pendulum became so associated with quality that decorative "fake" gridirons are often seen on pendulum clocks, that have no actual temperature compensation function.
The viscosity of the air through which the pendulum swings will vary with atmospheric pressure, humidity, and temperature. This drag also requires power that could otherwise be applied to extending the time between windings. Traditionally the pendulum bob is made with a narrow streamlined lens shape to reduce air drag, which is where most of the driving power goes in a quality clock. In the late 19th century and early 20th century, pendulums for precision regulator clocks in astronomical observatories were often operated in a chamber that had been pumped to a low pressure to reduce drag and make the pendulum's operation even more accurate.
To keep time accurately, pendulum clocks must be absolutely level. If they are not, the pendulum swings more to one side than the other, upsetting the symmetrical operation of the escapement. This condition can often be heard audibly in the ticking sound of the clock. The ticks or 'beats' should be at precisely equally spaced intervals to give a sound of, "tick...tock...tick...tock"; if they are not, and have the sound "tick-tock...tick-tock..." the clock is out of beat and needs to be leveled. This problem can easily cause the clock to stop working, and is one of the most common reasons for service calls. A spirit level or watch timing machine can achieve a higher accuracy than relying on the sound of the beat; precision regulators often have a built in spirit level for the task. Older freestanding clocks often have feet with adjustable screws to level them, more recent ones have a leveling adjustment in the movement. Some modern pendulum clocks have 'auto-beat' or 'self-regulating beat adjustment' devices, and don't need this adjustment.
Since the pendulum rate will increase with an increase in gravity, and local gravity varies with latitude and elevation on Earth, pendulum clocks must be readjusted to keep time after a move. For example, a pendulum clock moved from sea level to 4,000 feet (1,200 m) will lose 16 seconds per day. Even moving a clock to the top of a tall building will cause it to lose measurable time due to lower gravity.
Also called torsion-spring pendulum, this is a wheel-like mass (most often four spheres on cross spokes) suspended from a vertical strip (ribbon) of spring steel, used as the regulating mechanism in torsion pendulum clocks. Rotation of the mass winds and unwinds the suspension spring, with the energy impulse applied to the top of the spring. As the period of a cycle is quite slow compared to the gravity swing pendulum, it is possible to make clocks that need to be wound only every 30 days, or even only once a year or more. A clock requiring only annual winding is sometimes called a "400-Day clock", "perpetual clock" or "anniversary clock", the latter sometimes given as a wedding memorialisation gift. Schatz and Kundo, both German firms, were once the main manufacturers of this type of clock. This type is independent of the local force of gravity but is more affected by temperature changes than an uncompensated gravity-swing pendulum.
The escapement drives the pendulum, usually from a gear train, and is the part that ticks. Most escapements have a locking state and a drive state. In the locking state, nothing moves. The motion of the pendulum switches the escapement to drive, and the escapement then pushes on the pendulum for some part of the pendulum's cycle. A notable but rare exception is Harrison's grasshopper escapement. In precision clocks, the escapement is often driven directly by a small weight or spring that is re-set at frequent intervals by an independent mechanism called a remontoire. This frees the escapement from the effects of variations in the gear train. In the late 19th century, electromechanical escapements were developed. In these, a mechanical switch or a phototube turned an electromagnet on for a brief section of the pendulum's swing. These were used on some of the most precise clocks known. They were usually employed with vacuum pendulums on astronomical clocks. The pulse of electricity that drove the pendulum would also drive a plunger to move the gear train.
In the 20th century, W.H. Shortt invented a free pendulum clock / Shortt-Synchronome clock with an accuracy of one-hundredth of a second per day. In this system, the timekeeping pendulum does no work and is kept swinging by a push from a weighted arm (gravity arm) that is lowered onto the pendulum by another (slave) clock just before it is needed. The gravity arm then pushes on the free pendulum, which releases it to drop out of engagement at a time that is set entirely by the free pendulum. Once the gravity arm is released, it trips a mechanism to reset itself ready for release by the slave clock. The whole cycle is kept synchronised by a small blade spring on the pendulum of the slave clock. The slave clock is set to run slightly slow, and the reset circuit for the gravity arm activates a pivoted arm that just engages with the tip of the blade spring. If the slave clock has lost too much time, its blade spring pushes against the arm and this accelerates the pendulum. The amount of this gain is such that the blade spring doesn't engage on the next cycle but does on the next again. This form of clock became the standard for use in observatories from the mid-1920s until superseded by quartz technology.
The indicating system is almost always the traditional dial with moving hour and minute hands. Many clocks have a small third hand indicating seconds on a subsidiary dial. Pendulum clocks are usually designed to be set by opening the glass face cover and manually pushing the minute hand around the dial to the correct time. The minute hand is mounted on a slipping friction sleeve which allows it to be turned on its arbor. The hour hand is driven not from the wheel train but from the minute hand's shaft through a small set of gears, so rotating the minute hand manually also sets the hour hand.
Pendulum clocks were more than simply utilitarian timekeepers; they were status symbols that expressed the wealth and culture of their owners. They evolved in a number of traditional styles, specific to different countries and times as well as their intended use. Case styles somewhat reflect the furniture styles popular during the period. Experts can often pinpoint when an antique clock was made within a few decades by subtle differences in their cases and faces. These are some of the different types of pendulum clocks:
|Wikimedia Commons has media related to Pendulum clocks.|