From Wikipedia, the free encyclopedia - View original article
|This article needs additional citations for verification. (August 2012)|
netstat (network statistics) is a command-line tool that displays network connections for the Transmission Control Protocol (both incoming and outgoing), routing tables, and a number of network interface (network interface controller or software-defined network interface) and network protocol statistics. It is available on Unix-like operating systems including OS X, Linux, Solaris, and BSD, and is available on Windows NT-based operating systems including Windows XP, Windows Vista, Windows 7 and Windows 8.
It is used for finding problems in the network and to determine the amount of traffic on the network as a performance measurement.
Parameters used with this command must be prefixed with a hyphen (-) rather than a slash (/). If a parameter is supported only on some platform or platforms, the platform or platforms is listed in parentheses after the parameter.
|-a||Displays all active connections and the TCP and UDP ports on which the computer is listening.|
|-b (Windows)||Displays the binary (executable) program's name involved in creating each connection or listening port. (Windows XP, 2003 Server and newer Windows operating systems; not Microsoft Windows 2000 or older).|
|-b (OS X, NetBSD)||Causes -i to report the total number of bytes of traffic.|
|-e||Displays ethernet statistics, such as the number of bytes and packets sent and received. This parameter can be combined with -s.|
|-f (Windows)||Displays fully qualified domain names <FQDN> for foreign addresses (only available on Windows Vista and newer operating systems).|
|-f Address Family (FreeBSD)||Limits display to a particular socket address family, unix, inet, inet6|
|-g||Displays multicast group membership information for both IPv4 and IPv6 (may only be available on newer operating systems)|
|-i||Displays network interfaces and their statistics (not available under Windows)|
|-m||Displays the memory statistics for the networking code (STREAMS statistics on Solaris).|
|-n||Displays active TCP connections, however, addresses and port numbers are expressed numerically and no attempt is made to determine names.|
|-o (Windows)||Displays active TCP connections and includes the process ID (PID) for each connection. You can find the application based on the PID on the Processes tab in Windows Task Manager. This parameter can be combined with -a, -n, and -p. This parameter is available on Microsoft Windows XP, 2003 Server (and Windows 2000 if a hotfix is applied).|
|-p protocol (Windows and BSD)||Shows connections for the protocol specified by protocol. In this case, protocol can be tcp, udp, tcpv6, or udpv6. If this parameter is used with -s to display statistics by protocol, protocol can be tcp, udp, icmp, ip, tcpv6, udpv6, icmpv6, or ipv6.|
|-p (Linux)||Show which processes are using which sockets (similar to -b under Windows) (you must be root to do this)|
|-P protocol (Solaris)||Shows connections for the protocol specified by protocol. In this case, protocol can be ip, ipv6, icmp, icmpv6, igmp, udp, tcp, or rawip.|
|-r||Displays the contents of the IP routing table. (This is equivalent to the route print command under Windows.)|
|-s||Displays statistics by protocol. By default, statistics are shown for the TCP, UDP, ICMP, and IP protocols. If the IPv6 protocol for Windows XP is installed, statistics are shown for the TCP over IPv6, UDP over IPv6, ICMPv6, and IPv6 protocols. The -p parameter can be used to specify a set of protocols.|
|-t (Linux)||Display only TCP connections.|
|-W (FreeBSD)||Display wide output - doesn't truncate hostnames or IPv6 addresses|
|-v (Windows)||When used in conjunction with -b it will display the sequence of components involved in creating the connection or listening port for all executables.|
|Interval||Redisplays the selected information every Interval seconds. Press CTRL+C to stop the redisplay. If this parameter is omitted, netstat prints the selected information only once.|
|Displays help at the command prompt.|
Netstat provides statistics for the following:
To display the statistics for only the TCP or UDP protocols, type one of the following commands:
netstat -sp tcp
netstat -sp udp
On Microsoft Windows:
netstat -o 5
netstat -aop | grep "pid"
Some versions of
netstat lack explicit field delimiters in their printf-generated output, leading to numeric fields running together and thus corrupting the output data.
Under Linux, raw data can often be obtained from the /proc/net/dev to work around the printf output corruption arising in netstat's network interface statistics summary,
netstat -i, until such time as the problem is corrected.
On the Windows platform, netstat information can be retrieved by calling the GetTcpTable and GetUdpTable functions in the IP Helper API, or IPHLPAPI.DLL. Information returned includes local and remote IP addresses, local and remote ports, and (for GetTcpTable) TCP status codes. In addition to the command-line netstat.exe tool that ships with Windows, GUI-based netstat programs are available.
On the Windows platform running Remote Desktop Services (formerly Terminal Services) it will only show connections for the current user, not for the whole computer.
This program is obsolete. Replacement for netstat is ss. Replacement for netstat -r is ip route. Replacement for netstat -i is ip -s link. Replacement for netstat -g is ip maddr.