Chrysler Turbine Car

From Wikipedia, the free encyclopedia - View original article

Chrysler Turbine Car
Chrysler 027.jpg
Overview
ManufacturerChrysler Corporation
Production1963
55 produced
DesignerElwood Engel
Body and chassis
ClassConcept car
Body style2-door coupe
LayoutFR layout
Powertrain
EngineChrysler A831 gas turbine
Dimensions
Wheelbase110 in (2,794 mm)[1]
Length201.6 in (5,121 mm)[2]
Width72.9 in (1,852 mm)
Height53.5 in (1,359 mm) (loaded)
 
Jump to: navigation, search
Chrysler Turbine Car
Chrysler 027.jpg
Overview
ManufacturerChrysler Corporation
Production1963
55 produced
DesignerElwood Engel
Body and chassis
ClassConcept car
Body style2-door coupe
LayoutFR layout
Powertrain
EngineChrysler A831 gas turbine
Dimensions
Wheelbase110 in (2,794 mm)[1]
Length201.6 in (5,121 mm)[2]
Width72.9 in (1,852 mm)
Height53.5 in (1,359 mm) (loaded)

Chrysler Turbine Cars are automobiles powered by gas turbine engines that the Chrysler Corporation made from 1962-1964. Bodies for the Chrysler Turbine were made by Ghia in Turin, Italy, with final assembly taking place in a small plant in Detroit, Michigan, USA. After a period of testing, the vehicles were reclaimed by Chrysler; all but nine were destroyed. Three functioning examples remain, all in museums, and six more non-functioning examples in other museums.

Project Overview[edit]

The Chrysler Turbine Car was the first and only consumer test ever conducted of gas turbine-powered cars. Of the total 55 units built (5 prototypes and 50 "production" cars), most were scrapped at the end of a trial period, with only nine remaining in museums and private collections. Though Chrysler's turbine engine project was terminated in 1977, the Turbine Car was the high point of a three decade project to perfect the engine for practical use.

Engine[edit]

Engine compartment of a Chrysler 1963 Turbine car

The fourth-generation Chrysler turbine engine runs at up to 44,500 revolutions per minute, according to the owner's manual,[3] and could operate using diesel fuel, unleaded gasoline, kerosene, JP-4 jet fuel, and even vegetable oil. The engine can run on virtually anything with combustible properties and "Chrysler claimed the turbine could gulp everything from peanut oil to Chanel No. 5."[4] No air/fuel adjustments are required to switch from one fuel type to another and the only evidence of which fuel was used is the odor of the exhaust.

The engine has just 1/5 of the moving parts of a traditional piston-based internal combustion engine (60 rather than 300).[5] The turbine spins on simple sleeve bearings for vibration-free running. Its simplicity offers the potential for long life, and because no combustion contaminants enter engine oil, no oil changes are considered necessary. The 1963 Turbine's engine generated 130 brake horsepower (97 kW; 132 PS) and an instant 425 pound force-feet (576 N·m) of torque at stall speed, making it good for 0 to 60 mph (0 to 97 km/h) in 12 seconds at an ambient temperature of 85 °F (29 °C)—it can sprint quicker if the ambient air was cooler and denser.

The lack of many moving parts and the lack of liquid coolant eases maintenance, while the exhaust does not contain carbon monoxide, unburned carbon, or raw hydrocarbons. Nevertheless, the turbine generates nitrogen oxides and the challenge of limiting them proved an ongoing problem throughout development.

The power turbine is connected, without a torque converter, through a gear reduction unit to an only moderately modified TorqueFlite automatic transmission. The flow of the combustion gases between the gas generator and free power turbine provides the same functionality as a torque converter but without using a conventional liquid medium. Twin rotating recuperators transfer exhaust heat to the inlet air, greatly improving fuel economy. Varying stator blades prevent excessive top end speeds, and provide engine braking on deceleration.

Throttle lag and exhaust gas temperatures at idle plague early models; Chrysler was able to remedy or mitigate these to some degree. Acceleration lag, however, remains a problem, and fuel consumption is excessive. Acceleration is outstanding provided the turbine is spun up (by applying power) prior to releasing the brakes. Otherwise it is mediocre. The Turbine Car also features a fully stainless steel exhaust system, the exits of which are flat in cross section. This was intended to spread the exhaust gases thinly and thus cool them further, in order to allow the vehicle to stand in traffic without risking damage to following traffic. The combustor, or burner, is somewhat primitive by the standards of modern turbojet engines. A single reverse-flow canister featuring a more-or-less standard spark plug for ignition is employed. Had the engine been further developed, annular combustion chambers along with a second power turbine might have improved power and economy even more. The transmission has "idle" instead of "neutral".[6]

The turbine car has some operational and aesthetic drawbacks. The car sounds like a giant vacuum cleaner, which was unexpected to consumers who were more familiar with the sound of a large American V8. That said, some observers admired the sound. High altitudes also cause problems for the combined starter-generator. Additionally, failing to follow the correct start-up procedure will cause the engine to stall; some drivers thought they could warm up the engine similar to the way they did with a gasoline engine. They would press the accelerator pedal to the floor before the engine had reached proper temperature. Instead of warming the engine, the excess fuel slowed the turbine down and resulted in the opposite of the desired effect. Doing this, however, did not do any permanent damage to the engine. In fact, it was possible to apply full throttle immediately after starting the engine without much fear of excessive wear. The engines were remarkably durable considering how fragile turbine engines are when compared to internal combustion piston engines. Troubles were remarkably few for such a bold experiment. It is not known how many testers made the mistake of using the leaded pump gas of the era; the tetraethyl lead leaves debilitating deposits within the engine. It was the one flammable liquid Chrysler recommended not be used; it was also by far the easiest fuel to obtain. Even so, more than 1.1 million test miles were accumulated by the 50 cars given to the public, and operational downtime stood at only 4%.

Design[edit]

Chrysler Turbine Car at the 1964 New York World's Fair

The bodies and interiors were crafted by Ghia in Italy. The mostly completed bodies were shipped to Chrysler's Greenfield Avenue turbine research center in Detroit for final assembly. Outsourcing this step may have saved some money for Chrysler, but between the expensive Ghia bodies and the cost of the engine, each car may have cost as much as $50,000 to build.[7][8] This would be over $350,000 in 2012 dollars. A total of 50 "production" Turbine Cars were built between October 1963 and October 1964,[9] plus five prototypes (three of which differed in roof/paint schemes).[7] As each body was finished and shipped to Detroit, Chrysler employees installed the gas turbine engines, Torqueflite transmissions, and electrical components to prepare the cars for use by the 203 motorists - 23 of them women - who were chosen to test them throughout the country.

The Turbine Car is a two-door hardtop coupe with four individual bucket seats, power steering, power brakes, and power windows. Its most prominent design features are two large horizontal taillights and nozzles (back-up lights) mounted inside a very heavy chrome sculptured bumper. Up front, the single headlamps are mounted in chrome nacelles with a turbine styling theme, creating a striking appearance. This theme is carried through to the center console and the hubcaps. Even the tires were specially made with small turbine vanes molded into the white sidewalls. It is finished in reddish-brown "Frostfire Metallic" paint, later renamed "Turbine Bronze" and made available on production automobiles. The roof is covered in black vinyl, and the interior features bronze-colored "English calfskin" leather upholstery with plush-cut pile bronze-colored carpet. Front suspension is upper and lower wishbones with coil springs and shock absorbers.[1]

The dashboard is lit using electroluminescent panels in the gauge pods and on a call-out strip across the dash. This system did not use bulbs; instead, an inverter and transformer raised the battery voltage to over 100 volts AC and passed that high voltage through special plastic layers, causing the gauges to glow with a blue-green light. Instead of a water temp. gauge, the Chrysler Turbine has a Turbine Inlet temp. gauge with numbers 500, 1,000, 1,500, and 2,000 degrees Fahrenheit.[10]

The car itself was designed in the Chrysler studios under the direction of Elwood Engel, who had worked for the Ford Motor Company before his move to Chrysler. The designer credited with the actual look of the car was Charles Mashigan, who designed a two-seat show car called the Typhoon,[11] which was displayed at the 1964 World's Fair in New York City. Engel used many older Ford styling themes. The rear taillight/bumper assembly was copied directly (with revisions) from a 1958 Ford styling study called the "La Galaxie". He used none of the themes associated with his 1964 Imperial. As Engel incorporated many of the design themes from the 1961 Thunderbird, and because the car was a four seater of similar size and appointment, many enthusiasts call the Ghia Turbine the "Englebird."

Suspension did not follow Chrysler's ubiquitous independent front longitudinal torsion bar system of the time, but rather featured contemporary designs using independent front suspension with a coil spring at each wheel. Rear suspension was more typical of Chrysler, with leaf springs and direct-acting shock absorbers.

Legacy[edit]

Chrysler Turbine Car at the 1999 Antique Automobile Club of America show in Hershey, PA

After Chrysler finished the user program and other public displays of the cars, 46 of them were destroyed. Chrysler announced that this was necessary to avoid a stiff tariff, but that was only part of the story. The destruction of the cars was in line with the automobile industry's practice of not selling non-production or prototype cars to the public. This practice was also later used by General Motors with its EV1.

Of the remaining nine cars, six had the engines de-activated and then they were donated to museums around the country. Chrysler retained three operational turbine cars for historical reasons; two of the three are now owned by the "WPC Museum". All of the turbine cars owned by the "WPC Museum" are in running condition at the archives of the museum. The last turbine car that is functional, owned by the Museum of Transportation in St. Louis, was photographed for Mopar Action magazine, and appears at car shows around the United States from time to time. One Turbine car is on display at The Henry Ford Museum in Dearborn, Michigan, and it was be part of the exhibition Driving America in early 2012.

Only two Chrysler Turbine Cars are in the hands of private collectors: One was purchased by private automobile collector Frank Kleptz of Terre Haute, Indiana and is functional. Kleptz's Turbine Car was originally donated to the former Harrah museum in Nevada. The second one is owned by comedian and television host Jay Leno, who purchased one of the three Chrysler Turbine Cars which had been originally retained by Chrysler.[12] Leno wrote that

Most were destroyed by Chrysler for tax and liability reasons, which is a shame, because to this day everyone who rides in a Turbine says, "Whoa, this feels like the future!" You turn the key and there's a big woosh and a complete absence of vibration... I think it's the most collectible American car—it was so different. Most of all, the Chrysler Turbine is a reminder that all the cool stuff used to be made in the U.S. I hope it will be again.[13]

Chrysler's turbine engine program did not die completely with the destruction of the Ghia cars. A new coupe body, which was to become the 1966 Dodge Charger was considered for a new generation turbine engine. Nevertheless, Chrysler went on to develop a sixth generation gas-turbine engine which did meet nitrogen oxide regulations, and installed it in a 1966 Dodge Coronet, though it was never introduced to the public.

A smaller, lighter seventh generation engine was produced in the early 1970s, when the company received a grant from the United States Environmental Protection Agency (EPA) for further development, and a special bodied turbine Chrysler LeBaron was built in 1977 as a prelude to a production run. By then the company was in dire financial straits and needed U.S. government loan guarantees to avoid bankruptcy. A condition of that deal was that gas-turbine mass production be abandoned because it was "too risky" for an auto company of Chrysler's size.

A Chrysler Turbine Car, painted white with blue racing stripes, featured in the 1964 film The Lively Set. The car, loaned to the producers by Chrysler, was one of the test 'mules', and was returned to Chrysler after production. It was among the cars scrapped.[citation needed]

While Chrysler's work with turbine engines never paid off in the retail automobile sector, the experiments proved fruitful with the incorporation of a Honeywell AGT1500 into a slightly different product, the M1 Abrams Main Battle Tank, developed in the late 1970s by Chrysler Defense (which was later sold to General Dynamics).

See also[edit]

References[edit]

  1. ^ a b Cheetham, Craig, ed. (2006). Ultimate American Cars. MBI Publishing. pp. 108–111. ISBN 978-0-7603-2570-4. Retrieved 2012-04-02. 
  2. ^ "1963 Chrysler Turbine Car Drivers Guide, page 27". Oldcarbrochures.com. Retrieved 2012-04-03. 
  3. ^ "Turbine Driver's Guide". Chrysler Corporation. Retrieved 2012-04-03. 
  4. ^ Auto Editors of Consumer Guide (11 November 2007). "1950s and 1960s Chrysler Turbine Concept Cars". HowStuffWorks.com. Retrieved 27 January 2014. 
  5. ^ Technical Information, Engineering Office (January 1979). "History of Chrysler Corporation gad turbine vehicles". Chrysler Corporation. Retrieved 2012-04-02. 
  6. ^ "1963 Chrysler Turbine Car Drivers Guide, page 11". Oldcarbrochures.com. Retrieved 2012-04-02. 
  7. ^ a b Auto Editors of Consumer Guide (2007-11-11). "1950s and 1960s Chrysler Turbine Concept Cars". HowStuffWorks. Retrieved 2012-04-02. 
  8. ^ Lehto, Steve (2010). Chrysler's Turbine Car: The Rise and Fall of Detroit's Coolest Creation. Chicago Review Press. ISBN 978-1-56976-549-4. 
  9. ^ Adler, Dennis; Shelby, Carroll (2008). 50 Cars to Drive. Globe Pequot Press. p. 74. ISBN 978-1-59921-230-2. Retrieved 2012-04-02. 
  10. ^ "1963 Chrysler Turbine Car Drivers Guide, page 6". Oldcarbrochures.com. Retrieved 2012-04-02. 
  11. ^ Samsen, John. "Chrysler Corp., Exner Concept Cars 1940 to 1961". automobileart. Retrieved 2012-04-02. 
  12. ^ Rubin, Neal (3 August 2009). "Jay Leno gets rare Chrysler, author gets plug for book". The Detroit News. Retrieved 2012-04-02. 
  13. ^ Leno, Jay. "Jay Leno Drives One of the Last Chrysler Turbines". Popular Mechanics, April 2011. Hearst Communication, Inc. Retrieved 22 August 2012. 

External links[edit]